![epson l386 network stting epson l386 network stting](https://i0.wp.com/www.driverwe.com/wp-content/uploads/2018/08/L380-2BEPSON.png)
This is required so that you can configure your printer's IP address from the iOS device.Īlmost there! Now that your printer and iOS device share the same IP address, you can carry out DHCP configuration. Your iOS device is now configured to communicate with your printer. Change the IP address, Subnet Mask and Router according to the network configuration ticket that was printed.Ħ. Tap the information icon beside the connected network.Ĥ.On the iOS device that you will be printing from, navigate to Settings > Wi-Fi.Temporarily connect iOS device to printer's IP address Then, you will enable DHCP configuration in order to assign the printer an IP address on your network. In order to connect your printer to your internet network, you will need to temporarily change the IP address on your iOS device to the printer's default IP. This is the default Epson IP address required to configure the printer's network settings. A status sheet should auto-print with an IP address of 192.168.192.168.This is also a useful action to understand if you ever need to verify your printer's network settings in the future. This ticket is required to confirm your printer's network settings. Follow the instructions below to print a status sheet, or network configuration ticket. If your printer is fresh out of the box, you may not need to begin with a factory reset.
![epson l386 network stting epson l386 network stting](https://files.support.epson.com/docid/cpd4/cpd42851/source/images/lcd_screens/xp820_860/lcd_home_xp820.jpg)
This IP address is the default Epson printer ID required in order to configure the printer for your network. After another 5 seconds or so, a network configuration ticket should auto-print with an IP address of 192.168.192.168.After 5 seconds, a ticket will print notifying of a factory reset. Release the reset button.While pushing the reset button, turn the printer on by pressing the power button.Turn the printer around and with a pen or pencil tip, push the pinhole reset button on the back of the printer for 4 seconds.To ensure the printer is not connected to another network, follow the instructions below to factory reset the printer's network settings: Connect the other end of the ethernet cable to an ethernet port on your internet router.īefore beginning DHCP network configuration, it's important to ensure your printer is not connected to another network with another IP address.Connect one end of the ethernet cable to the ethernet port at the bottom of your printer.Turn off the printer by pressing the power button.Once your printer is connected to your router, you are able to configure DHCP settings to ensure your printer and iOS device communicate with one another. Your iPad should be connected (by Wifi or LAN) to your internet, but a TM-T88VI LAN receipt printer needs to be directly connected to your internet router. In order for the Restaurant POS device to send print jobs to the Epson TM-T88VI, the iOs device and printer both need to be on the same network. Push the cover down to snap the lever back into place.Pull the paper out past the cutter at the front of the printer.While doing so, make sure the paper roll stays taut and doesn't unravel. Insert a paper roll with the paper pulling under and out (see image below).To open the printer cover, push the lever on the right-hand side of the printer away from you and lift the cover upwards.On top of the printer, press the power button and wait for the blue power light to appear.Connect the pronged end of the AC cable into an electrical power supply.Connect the female end of the AC cable into the pronged AC adapter socket.Connect the male end of the AC adapter into the circular power port at the bottom of your printer.Make sure you AC cable is not connected to a power supply (unplug if it is).iOS device installed with the latest Lightspeed Restaurant POS appĬonnect the receipt printer to a power supply.Router (we recommend routers set up in close proximity to your hardware and printers).Ethernet LAN cable (long enough to reach your router).To set up your receipt printer, you'll need the following equipment: Add the printer to Lightspeed Restaurant.Users can then print receipts to the TM-T88VI from an iOS device through a shared network connection.įollow the steps below when setting up your Epson TM-T88VI LAN receipt printer: The Epson TM-T88VI LAN thermal receipt printer connects directly to an internet router with an ethernet cable and DHCP configuration.